Manual / Guide · 2008

Sega Primeval Hunt DX — Service Manual

Lindbergh JVS I/O error codes.

Author: Sega
Year: 2008
Type: Manual / Guide
Credit: Sega. Copy via the Internet Archive (item 'primevalhuntdx')

primeval hunt
lindbergh
jvs
arcade

INTRODUCTION TABLE OF CONTENTS TABLE OF CONTENTS BEFORE USING THE PRODUCT ----------------------------------------------TABLE OF CONTENTS ----------------------------------------------------------------0 INTRODUCTION -----------------------------------------------------------------------0 COPYRIGHT AND LICENSE MARKS ---------------------------------------------- 0 i ii v vi 0 1 HANDLING PRECAUTIONS --------------------------------------------------------- 0 1 0 2 PRECAUTIONS REGARDING INSTALLATION LOCATION ---------------- 0 4 2.1 LIMITATION OF USE -------------------------------------------------------------------------- 0 4 2.2 OPERATION AREA ------------------------------------------------------------------------------0 5 0 3 PRECAUTIONS REGARDING PRODUCT OPERATION ------------------------- 0 6 3.1 BEF0RE OPERATION --------------------------------------------------------------------------- 0 6 3.2 PAYING ATTENTION TO CUSTOMER DURING OPERATION -------------------------- 0 8 0 4 PARTS DESCRIPTIONS -------------------------------------------------------------- 0 9 0 5 ACCESSORIES ------------------------------------------------------------------------- 0 10 0 6 ASSEMBLY AND INSTALLATION ------------------------------------------------- 0 12 6.1 GENERAL ASSEMBLY INFORMATION ----------------------------------------------------- 0 14 6.2 FIXING THE BILLBOARD AND POP --------------------------------------------------------- 0 15 6.3 FIXING THE GUN CONSOLE TO THE VIDEO CABINET ------------------------------- 0 17 6.4 INSTALLATION AND FIXING IN PLACE ---------------------------------------------------- 0 22 6.5 CONNECTING THE POWER CABLES -------------------------------------------------------- 0 23 6.6 CHECKING ASSEMBLY (SET UP) ------------------------------------------------------------0 25 0 7 PRECAUTIONS WHEN MOVING THE MACHINE ------------------------------- 0 29 0 8 GAME DESCRIPTION ---------------------------------------------------------------- 0 31 8.1 GAME OVERVIEW ------------------------------------------------------------------------------ 0 31 8.2 TOUCH PANEL CONTROL DURING GAME ------------------------------------------------ 0 34 8.3 BONUS GAME RULES -------------------------------------------------------------------------- 0 36 8.4 ITEMS - DEFINITION AND RULES ----------------------------------------------------------- 0 37 8.5 GAME FLOW DIAGRAM ----------------------------------------------------------------------- 0 38 8.6 MECHANISM OF CALCULATION ------------------------------------------------------------ 0 39 0 9 EXPLANATION OF TEST AND DATA DISPLAY --------------------------------- 0 41 9.1 SWITCH UNIT AND COIN METER ----------------------------------------------------------- 0 43 9.2 SYSTEM TEST MODE --------------------------------------------------------------------------- 0 44 9.3 GAME TEST MODE ----------------------------------------------------------------------------- 0 46 9.31 INPUT TEST ---------------------------------------------------------------------------0 47 9.32 OUTPUT TEST ------------------------------------------------------------------------ 0 48 9.33 SOUND ADJUSTMENT ------------------------------------------------------------- 0 49 9.34 GAME ASSIGNMENTS --------------------------------------------------------------0 50 9.35 TOUCH PANEL ADJUSTMENTS -------------------------------------------------- 0 52 9.36 GUN ADJUSTMENT ----------------------------------------------------------------- 0 54 9.37 BOOK-KEEPING --------------------------------------------------------------------- 0 56 9.38 BACK UP DATA CLEAR ------------------------------------------------------------- 0 59 9.39 INTERFERENCE PREVENTION WIRING ---------------------------------------- 0 60 0 TABLE OF CONTENTS 10 61 10.1 DISASSEMBLE GUN ---------------------------------------------------------------------------- 0 62 10.2 REASSEMBLING GUN ------------------------------------------------------------------------- 0 65 10.3 REPLACING GUN SPEAKER ------------------------------------------------------------------ 0 67 10.4 REPLACING GUN SENSOR UNIT ------------------------------------------------------------ 0 68 10.5 REPLACING GUN MICRO SWITCHES ------------------------------------------------------- 0 69 10.6 GUN PARTS LIST AND BREAKDOWN ------------------------------------------------------ 0 71 0 11 MONITOR UNIT ----------------------------------------------------------------------- 0 72 11.1 CAUTION AND WARNING CONCERNING MONITOR SAFETY ------------------------ 0 72 11.2 CLEANING CRT SURFACE --------------------------------------------------------------------- 0 73 11.3 ADJUSTMENT PROCEDURES ---------------------------------------------------------------- 0 74 11.4 TROUBLE SHOOTING -------------------------------------------------------------------------- 0 78 11.5 LAMP REPLACEMENT PROCEDURE ------------------------------------------------------- 0 84 0 12 COIN SELECTOR AND CREDIT SETTINGS --------------------------------------- 0 88 12.1 CLEANING THE COIN SELECTOR ------------------------------------------------------------ 0 88 12.2 ADJUSTING PRICE OF PLAY ----------------------------------------------------------------- 0 90 12.3 SR3 OPTIONS - TEACH AND RUN PROGRAMMING ------------------------------------ 0 94 0 13 FLUORESCENT LAMP REPLACEMENT ------------------------------------------- 0 96 0 14 PERIODIC INSPECTION -------------------------------------------------------------- 0 98 0 15 TROUBLE SHOOTING ---------------------------------------------------------------- 0 100 15.1 TROUBLE SHOOTING - (WHEN NO ERROR MESSAGE IS SHOWN) ------------------ 0 101 15.2 ERROR MESSAGES ----------------------------------------------------------------------------- 0 102 0 16 GAME BOARD ------------------------------------------------------------------------- 0 105 16.1 REMOVING THE LINDBERGH ---------------------------------------------------------------- 0 106 16.2 COMPOSITION OF THE GAME BOARD ---------------------------------------------------- 0 108 0 17 SOFTWARE INSTALLATION --------------------------------------------------------- 0 109 17.1 ATTACHING DVD DRIVE AND KEY CHIP -------------------------------------------------- 0 109 17.2 TURNING POWER ON - SOFTWARE INSTALLATION ----------------------------------- 0 111 0 18 DESIGN RELATED PARTS ----------------------------------------------------------- 0 117 19 PARTS LIST ---------------------------------------------------------------------------- 0 119 20 WIRING COLOUR CODE TABLE ----------------------------------------------------0 150 21 WIRING DIAGRAM ------------------------------------------------------------------- 0 151 0 0 0 21.1 WIRING DIAGRAM D 1-3 --------------------------------------------------------------------- 0 151 21.2 WIRING DIAGRAM D 2-3 --------------------------------------------------------------------- 0 152 21.3 WIRING DIAGRAM D 3-3 --------------------------------------------------------------------- 0 153 0 0 0 0 0 0 TABLE OF CONTENTS CONTROL PANEL - GUN ------------------------------------------------------------- 0 INTRODUCTION This manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electro-mechanicals, servicing control, spare parts, etc. for the product, “SEGA - PRIMEVAL HUNTER Deluxe” INTRODUCTION This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and suﬃciently understanding the instructions . In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician to touch the internal system. Turn oﬀ the power to the machine, making sure to unplug the electrical cord from the outlet, and contact the oﬃce listed below or the point of purchase for this product. Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special attention are indicated by bold text, the word “IMPORTANT” and the symbol below. Indicates important information that, if ignored, may result in the mishandling of the product and cause faulty operation or damage to the product. SEGA AMUSEMENTS EUROPE, LTD. Block C, 42 Barwell Business Park, Chessington, Surrey. KT9 2NY United Kingdom. Telephone: +44 (0) 208 391 8090 Facsimile: +44 (0) 208 391 8099 e-mail: [email protected] http://www.sega-amusements.co.uk SPECIFICATIONS MACHINE DETAILS Width : 1540mm Depth : 1750 mm Height： 2200 mm Weight： 303 kg Max. Power, Current： Ave. Power, Current : Voltage : Monitor Type： 460 W. 448 W. 220 - 230 Vac (60.5 inches) （69 inches） (86.6 inches (668 lbs) 2 Amps 50Hz 62” DLP Type Colour Display. NOTE : The contents herein described are subject to change without notice. Deﬁnition of 'Site Maintenence Personnel or Other Qualiﬁed Individuals' Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel or other qualiﬁed professionals. This manual includes directions for potentially dangerous procedures which should only be carried out by professionals with the appropriate specialised knowledge. The site maintenance personnel or other qualiﬁed professionals mentioned in this manual are deﬁned as follows: Site maintenance personnel: Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the supervision of the owner/operator of this product to maintain machines within amusement facilities or similar premises by carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/expendable parts. Activities to be carried out by site maintenance personnel: Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/ expendable parts. Other qualiﬁed professionals: Persons employed by amusement equipment manufacturers, or involved in design, production, testing or maintenance of amusement equipment. The individual should have either graduated from technical school or hold similar qualiﬁcations in electrical/electronics/mechanical engineering. Activities to be carried out by other qualiﬁed professionals: Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/ mechanical parts. INTRODUCTION Procedures not described in this manual or marked as ʻto be carried out by site maintenance personnel or other qualiﬁed professionalsʼ should not be carried out by personnel without the necessary skill or technology. Work carried out by unqualified persons may cause serious accidents, including electrocution. COPYRIGHT and LICENCE MARK LICENSE MARK INTRODUCTION Copyright © 1994-2007 Lua.org, PUC-Rio. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. Copyright © 1999-2000 Pawel W. Olszta. All Rights Reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation ﬁles (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies or substantial portions of the Software. The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT. IN NO EVENT SHALL PAWEL W. OLSZTA BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. Except as contained in this notice, the name of Pawel W. Olszta shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization from Pawel W. Olszta. The Font to be used in the game The typefaces included herein are solely developed by DynaComware. 1 HANDLING PRECAUTIONS When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine. 1 • To avoid an electric shock or short circuit, do not plug in or unplug quickly. • To avoid an electric shock, do not plug in or unplug with a wet hand. • Do not expose power cords or earth wires on the surface, (ﬂoor, passage, etc.). If exposed, the power cords and earth wires are susceptible to damage. Damaged cords and wires can cause an electric shock or short circuit. • To avoid causing a ﬁre or an electric shock, do not put things on or damage the power cords. • When or after installing the product, do not unnecessarily pull the power cord. If damaged, the power cord can cause a ﬁre or an electric shock. • In case the power cord is damaged, ask for a replacement through where the product was purchased from or the oﬃce herein stated. Using the cord as is damaged can cause ﬁre, an electric shock or leakage. • Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. • Be sure to use fuses meeting the speciﬁed rating. Using fuses exceeding the speciﬁed rating can cause a ﬁre or an electric shock. • Be sure that connections such as IC BD are made properly. Insuﬃcient insertion can cause an electric shock. • Speciﬁcation changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted. - Failure to observe this may cause a fire or an electric shock. Non-compliance with this instruction can have a bad influence upon physical conditions of the players or the onlookers, or result in injury during play. - SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by speciﬁcation changes not designated by SEGA. • If work or parts replacement not indicated in this manual is carried out, an accident may occur. If it is necessary to carry out work not indicated in this manual, be sure to have it done by the oﬃce indicated in this manual or by the point of purchase. Also, please inquire regarding details of the work involved. • Be sure to perform periodic maintenance inspections herein stated. HANDLING PRECAUTIONS • Before performing work, be sure to turn the power oﬀ. Performing the work without turning the power oﬀ can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always states to that eﬀect. • For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard. 1 HANDLING PRECAUTIONS • When cleaning the CRT surfaces, use a soft and dry cloth. Do not apply chemicals such as thinners, benzene, etc. • Static electricity from your body may damage some electronics devices on the IC board. Before handling the IC board, touch a grounded metallic surface so that the static electricity can be discharged. • Do not turn the power on and oﬀ continuously. Repeatedly turning the power on and oﬀ may cause product malfunction or parts damage. • Some parts are not designed and manufactured speciﬁcally for this game machine. The manufacturers may discontinue, or change the speciﬁcations of such general-purpose parts. If this is the case, SEGA cannot repair or replace a failed game machine whether or not a warranty period has expired. CONCERNING THE WARNING LABELS This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical Specifications. It also has a Sticker describing where to contact for repair and for purchasing parts. When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker. The Serial Number indicates the product register. Identical machines could have diﬀerent parts depending on the date of production. Also, improvements and modifications might have been made after the publication of this manual. In order to ensure you order the correct parts, mention the Serial No. when contacting the applicable places. This SEGA product has warning displays on stickers, labels and/or printed instructions adhered/attached to or incorporated in the places where a potentially hazardous situation could arise. The warning displays are intended for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing work. Some portions of the cabinet contain high voltage and may cause accidents if touched. When performing maintenance, be very careful of the warning displays. It is especially important that any complex repair and replacement work not mentioned herein should be performed by those technical personnel who have knowledge of electricity and technical expertise. In order to prevent accidents, caution any customer ignoring the warnings to cease and desist immediately 1 HANDLING PRECAUTIONS CONCERNING THE STICKER DISPLAY 2 PRECAUTIONS REGARDING INSTALLATION LOCATION This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a ﬁre, electric shock, injury and/or malfunction. 2 PRECAUTIONS REGARDING INSTALLATION LOCATION - Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and/or shower, etc. - Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. - Places ﬁlled with inﬂammable gas or vicinity of highly inﬂammable/volatile chemicals or hazardous matter. - Dusty places. - Sloped surfaces. - Places subject to any type of violent impact. - Vicinity of anti-disaster facilities such as ﬁre exits and ﬁre extinguishers. - Areas where the temperature exceeds the applicable temperature (ambient temperature) range of 5 to 30 degrees centigrade. 2-1 LIMITATAION OF USE Be sure to check the Electrical Speciﬁcations. Ensure that this product is compatible with the locationʼ s power supply, voltage, and frequency requirements. A plate describing Electrical Speciﬁcations is attached to the product. Non-compliance with the Electrical Speciﬁcations can cause a ﬁre and electric shock. This product requires a breaker and earth mechanism as part of the location facilities. Using the product without these can cause a ﬁre and electric shock. Ensure that the indoor wiring for the power supply is rated at 15 A or higher (AC single phase 100 V ~ 120 V area), and 7 A or higher (AC 220 V ~ 240 V area). Non-compliance with the Electrical Speciﬁcations can cause a ﬁre and electric shock. Be sure to use an independent power supply equipped with an earth leakage breaker. Using a power supply without an earth leakage breaker can cause an outbreak of ﬁre if a power surge occurs. Putting many loads on one electrical outlet can cause generation of heat and a ﬁre resulting from overload. When using an extension cord, ensure that the cord is rated at 15 A or higher (AC 100 V ~ 120 V area) and 7 A or higher (AC 220 V ~ 240 V area). Using a cord rated lower than the speciﬁed rating can cause a ﬁre and electric shock. 2-2 OPERATIONAL AREA • Be sure to provide suﬃcient space speciﬁed in this manual. Do not allow objects to block the ventilation ports. It can cause generation of heat and a ﬁre. • SEGA shall not be held responsible for damage or compensation for damage to a third party, resulting from the failure to observe this instruction. In order to transport the machine into a building, the minimum necessary dimensions of the opening (of doors, etc,) are 0.8m, (W) and 2m, (H). 2-2 Fig 02 2-2 Fig 01 Before leaving the machine after Installation, make sure that the Castor Lift Adjusters are ﬁrmly positioned on the ground and that the machine is totaly stable. 2 PRECAUTIONS REGARDING INSTALLATION LOCATION • For the operation of this machine, secure a minimum area of 2.6 m [W] x 3 m [D]. The dimensions of the base periphery are established in consideration of ventilation, maintenance and customer passage. And if they fall and hit their head, there could be a very serious injury. Be sure to always secure enough space as prescribed in this manual. 3 PRECAUTIONS REGARDING PRODUCT OPERATION 3-1 BEFORE OPERATION To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players 3 PRECAUTION REGARDING PRODUCT OPERATION In order to avoid accidents, check the following before starting the operation: To ensure maximum safety for the players and the customers, ensure that where the product is operated has suﬃcient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and/or trouble between customers. Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitorʼ s flickering or deviation as is. Failure to observe this can have a bad influence upon the playersʼ or the customersʼ physical conditions. It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest Do not put any heavy items on this product. Placing any heavy item on the product can cause an accident or parts damage if it falls. Do not climb on the product. Climbing on the product can cause an accident by falling. To check the top portion of the product, use a step ladder. To avoid electric shock, short circuit and / or parts damage, do not put the following items on or in the periphery of the product. Flower vases, ﬂower pots, cups, water tanks, cosmetics, receptacles or vessels containing chemicals or water. Check that all of the adjusters are in contact with the ﬂoor surface. If they are not, the cabinet can move and cause an accident. 3-1 BEFORE OPERATION ● During daily cleaning, be sure to check the ʻTouch Panelʼ for any abnormality, wetness, stickiness, etc. Failure to do this may result in deliberate tampering or negligence being left undetected. ● To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause contact, collisions and or trouble between customers. ● Do not attempt to clean this product using pressurised equipment such as a jet wash or hose. If for any reason this product becomes wet, do not use until it has completely dried. Players hold the controller with their bare hands so it is recommended that wet towels (paper towels) be provided. 3 PRECAUTIONS REGARDING PRODUCT OPERATION ● During daily cleaning be sure to check the surface of the Guns and other parts that the player touches with his hands for damage, cracks or loose screws. If a player uses the machine while it is damaged, cracked or has a loose screw, the player may become injured. 3-2 PAYING ATTENTION TO CUSTOMERS DURING OPERATION To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players. 3 ● For safety reasons, do not allow any of the following people to play the game. PRECAUTION REGARDING PRODUCT OPERATION ・Those who need assistance when walking. ・Those who have high blood pressure or heart problems. ・Those who have a neck or spinal cord problem. ・Those who have experienced muscle convulsion or loss of consciousness while playing video games, etc. ・Those who are intoxicated or under the inﬂuence of drugs. ・Pregnant women. ・Those who are not in good health. ・Those who do not follow the attendants instructions. ・Those who cannot grasp the controller unit securely because of immobility in ﬁngers, hands or arms. ・Persons who disregard the products warning labels. ● Even players who have never been adversely affected by light stimulus might experience dizziness or headaches depending on their physical condition when playing the game. Small children are especially likely to experience these symptoms. Caution guardians of small children to keep watch on their children during play. ● Instruct those who feel sick during pay to seek medical advice or examination. ● To avoid injury from falling objects or electric shock hazard from split drinks, instruct the player not to place drinks or heavy items on the product. ● To avoid electric shock hazard and short circuit hazard, do not allow customers to put hand or ﬁngers or any other extraneous matter in to the openings of the product or small openings on or around the doors. ● To avoid falls resulting in injury, immediately stop the customer from leaning against or climbing on the product. ● To avoid electric shock and/or short circuit hazard, do not allow customers to unplug the power plug without a justiﬁable reason. Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or cause the cabinet to fall over, resulting in injury. 4 PART DESCRIPTIONS 4 Part Descriptions ITEM WIDTH (cm) DEPTH (cm) VIDEO CABINET GUN CONSOLE BILLBOARD WHEN ASEMBLED 1540 810 1540 1540 600 1150 510 1750 HEIGHT (cm) WEIGHT (kg) 2250 935 385 2250 202 80 21 303 5 ACCESSORIES Conﬁrm that the accessories list in the table below are present when setting up the product. Accessories marked “Spare” in the note column are consumable items but included as spares. TABLE 5A - ACCESSORIES 5 ACCESSORIES DESCRIPTION OWNERS MANUAL PT NUMBER (QTY) 420-0004-01UK (2) NOTE This Manual Parts not labeled with part numbers are as yet unregistered or cannot be registered. Be sure to handle all parts with care, as some parts are not available for purchase as separate items. KEY MASTER 220-5793-2-A001 (2) For opening/closing the doors KEY (2) CASHBOX DOOR LINDBERGH RED SERVICE MANUAL 420-7032-A001 (1) Explanation of built in Game Board MAINS LEADS LM1227 (1xUK) LM1246 (1xEURO) TAMPER PROOF SCREW WRENCH M4 540-0006-01 (1) SEQ 404 405 407 408 409 410 411 412 413 414 415 416 417 425 NUMBER 540-0006-01 420-7032-01UK 420-0004-01UK OS1019 440-CS0186UK SAECE-xxx LM1227 LM1246 PK0434 PK0435 PK0438 PK0439 ADH-PO18-2UK PK0 446 DESCRIPTION WRENCH M4 TMP PRF LINDBURGH RED MANUAL SERVICE MANUAL - ADH DX SELF SEAL BAG 9 x12. 3/4 STICKER C - EPILEPSY MULTI DECLARATION OF CONFORMITY UK MAINS LEAD 10A WITH PLUG EUROLEAD 10A EUROPEAN SOCKET PALLET - ADH FRONT CABINET SHRINK BAG - ADH FRONT CABINET PALLET - ADH DLP CABINET SHRINK BAG - ADH DLP CABINET INST DECAL MULTI BOX - BILLBOARD ADH DX REMOTE CONTROL for 62" DPL QUANTITY 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 NOTE SPARE SPARE SPARE SPARE SPARE 5 ACCESSORIES Conﬁrm that the accessories list in the table below are present when setting up the product. Accessories marked “Spare” in the note column are consumable items but included as spares. TABLE 5B - ACCESSORIES To order a duplicate “GAME DISC” DVD only, Please quote the following : Part Number : 610-0726-0048 : DVD SOFT ADH 5 ACCESSORIES KEY CHIP (1) CUSHION SPONGE 601-11137 (1) Protective Material GAME DISC (1) DISC CASE NOTE : The KEY CHIP has been already ﬁtted into the LINDBERGH Game Board and the GAME SOFTWARE has been pre-installed. Only use the “GAME DISC” DVD when necessary, for some reason such as replacing the LINDBERGH. However to Install the Software you will require a DVD DRIVE and USB Cable (mini type). If you do not have these available, a “DVD DRIVE KIT” has been made available for purchase from your supplier. See below for kit details. TABLE 5C XKT-1515-01 : DVD DRIVE KIT FOR LINDBERGH. SERVICE MANUAL 420-6923-01 (1) DVD DRIVE 610-0719-01-91 (1) For software installation. See “Chapter 17” DVD WIRE 605-0094 (1) For software installation. 6 ASSEMBLY & INSTALLATION 6 ASSEMBLY & INSTALLATION • This work should be carried out by site maintenance personnel or other qualified professionals. Work performed by non-technical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation. If no one with proper technological expertise is available, request service from the oﬃce indicated in this document or the point of purchase so as to ensure safety. • Perform assembly work by following the procedure herein stated. Failure to comply with the instructions can cause electric shock. • Perform assembling as per this manual. Since this is a complex machine, incorrect assembling can cause an electric shock, machine damage and/or improper functioning as per speciﬁed performance. • When assembling, more than one person is required. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage. • Ensure that connectors are properly connected. Improper connections can cause electric shock. • Be careful not to damage the wires. Damaged wires may cause electric shock or short circuit or present a risk of ﬁre. • Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be diﬃcult. • To perform work safely and avoid serious accident such as the cabinet falling down, do not perform work in places where step-like grade diﬀerences, a ditch, or slope exist. • Do not leave power cords, ground wires or network cables in areas of heavy foot traﬃc. Doing so may cause them to become damaged, possibly resulting in electric shock and/or short circuits. When leaving wiring across a ﬂoor, always use a safety covers to protect the wires. (Wiring diameter : Power Cables - approx 0.8, Network Cable approx 0.5) • The power cord for this product has a ground terminal. Make sure to use this ground termination when plugging it into an indoor outlet. Failure to ground the product could lead to electrocution. It can also cause malfunction. • Do not use connectors other than those connected to and used by the game board at the time of shipment. Do not connect wires to unused connectors. This could cause the generation of heat or smoke, or a burnout. • Wear appropriate work clothing so that work can be performed safely. Use gloves and safety shoes to prevent accidents or injuries. • When installing a wire protection cover over a ﬂoor, use a material shaped so that no one passing by will stumble over it. Using a material that could be stumbled over might lead to an accidental fall. • Handle plastic parts with care. Excessive weight or pressure may cause them to break and the broken pieces may cause injury. • When opening/closing, attaching/removing doors or lids, be careful that your hands or ﬁngers etc, does not get caught in the apparatus. Installation and assembly of this product should take place in the following sequence. GENERAL ASSEMBLY INFORMATION 6-2 FITTING THE BILLBOARD AND POP 6-3 FIXING THE GUN CONSOLE TO THE VIDEO CABINET 6-4 INSTALLATION AND SECURING IN PLACE 6-5 CONNECTING POWER CABLE AND GROUND 6-6 CHECKING ASSEMBLY (SET UP) 6 ASSEMBLY & INSTALLATION 6-1 6-1 GENERAL ASSEMBLY INFORMATION There are three MAIN Assemblies supplied, that have to be ﬁtted together in order to complete the built of this machine : A - Video Cabinet B - Billboard C- Console 6 (Video Cabinet Assembly) (Billboard Assembly) (Gun Console and Touch Panel Assembly) ASSEMBLY & INSTALLATION (Note that the Video Cabinet ʻAʼ is sub divided into three further component parts : A1 - Video Top, A2 - Video Base and A3 - Spacer, this will be explained latter.) 6-1 Fig 01 6-2 FITTING THE BILLBOARD AND POP The BILLBOARD weighs 21Kgs (46.3lbs) therefore this installation should not be attempted single handed. It is recommended that three persons undertake this particular section of the installation. 3-2 Fig 01 Shows the key ﬁxing points to be considered when attaching the BILLBOARD to the VIDEO Cabinet. 3-2 Fig 02 Shows the components to be used during this section of the assembly. 3-2 Fig 03 Shows the assembly completed at the end of this section of the assembly. 6-2 Fig 01 6-2 Fig 02 6-2 Fig 03 ASSEMBLY & INSTALLATION WORK SHOULD NOT BE UNDERTAKEN ON TOP OF THE CABINET WITHOUT THE USE OF A SUITABLE STEP OR FOOTSTOOL. 6 6-2 FITTING THE BILLBOARD AND POP starting the installation, locate 1 Before the WIRE HARNESS in Billboard. See (6-2 Fig 01) for the locations where the Harness will be are found. 6 6-2 Fig 04 ASSEMBLY & INSTALLATION Once you have located the harness, get at least two people to lift the Billboard up onto the top of the Video Cabinet. Then with one person supporting the right hand side and the other lifting the left hand side up, locate the harnesses in the billboard and connect it to the connector in the top of the Video Cabinet. the Harness are connected, 2 Once lower the Billboard down onto the top of the cabinet approx 25mm from the front edge of the cabinet making sure that the two Fixing Lugs located towards the front edge, go through the Lug Location Points cutouts the underside of the Billboard. 6-2 Fig 05 the Billboard sitting ﬂat on top 3 When the Cabinet, ﬂush with both sides and the Fixing Lugs through the location cutouts either end of the Billboard base. Slide the Billboard forward until the bottom edge is ﬂush with the front of the Cabinet. Check that both of the Fixing Lugs have located inside the Billboard and the front is ﬁrmly held. To complete the assembly ﬁt the two fixing screws through the Billboard into the cabinet along the back edge. 6-2 Fig 06 6-3 FIXING THE GUN CONSOLE TO THE VIDEO CABINET Whenever moving the unit, manipulate the movement from either end of the cabinet. Never push or pull the unit from the front or backside, as this can cause the unit to topple over causing damage to the unit and possible injury to any persons in the locality. The VIDEO CABINET UNIT has three basic cabinet component parts : A1 - Video Top, A2 - Video Base A3 - Spacer (See 6-1 Fig 01). A1 the Video Top is only placed on top of A2 the Video Base, there are NO direct ﬁxing between the two units. However there is an indirect ﬁxing between the units via A3 the Spacer, where the bottom ﬁxings are located in the front of the A2 the Base Unit, and the top ﬁxings being located in the front of A1 the Video Unit. This connection helps steady the Unit during transport. 1 Position the Video Cabinet in the approx area of operation, allowing room to gain access from all sides. Remove the eight Fixing Bolts from the SPACER, (four bolts from each side) and remove the SPACER from the VIDEO CABINET, keeping the bolts safe. 6-3 Fig 01 6-3 Fig 02 6 ASSEMBLY & INSTALLATION The MAIN VIDEO Cabinet with BILLBOARD Fitted Weights approx 223Kgs (492lbs) therefore a minimum of two people are required when moving this unit. Great care should be taken when handling or moving the unit otherwise personal injury may occur. 6-3 FIXING THE GUN CONSOLE TO THE VIDEO CABINET 2 Fitting the GUN CONSOLE and SPACER together. 6 ASSEMBLY & INSTALLATION 1 1. Get the GUN CONSOLE ʻCʼ ready to have the SPACER ﬁtted. C 2. Get the SPACER ʻA3ʼ and you will see a wooden cleat sticking out from the outside face. 3. Place the outside face of the Spacer against the back face of the Console, with the wooden cleat sitting on the bottom edge of the cut out. 2 4. Hold in place and ﬁt the seven ﬁxing bolts with ﬂat and spring washers into the locations shown. A3 C 4 3 6-3 Fig 03 6-3 Fig 04 6-3 FIXING THE GUN CONSOLE TO THE VIDEO CABINET 3 Identifying the VIDEO Cabinet Interconnection cables. The Wire Harness will connect into a matching harness that will be found in the back of the Gun Console. The Video Cable will pass through into the Gun Console and connect directly to the LINBURGH Game board. You will also ﬁnd the Common EARTH Point just inside the opening. 6 ASSEMBLY & INSTALLATION Inside the front of the VIDEO CABINET you will ﬁnd a Wiring Harness with several connectors and also a long Video Cable. 6 6-3 FIXING THE GUN CONSOLE TO THE VIDEO CABINET 4 Identifying the CONSOLE Cabinet components In the back of the Console ASSEMBLY & INSTALLATION you will find two Grn-Yel Ground wires, these wire must be unwound, passed through to the Video Cabinet and ﬁrmly connected to the Common Earth Point. The Video Cable from the Video Cabinet is feed through the Console and connects to the LINBURGH as indicated below. 6-3 FIXING THE GUN CONSOLE TO THE VIDEO CABINET 5 Connecting the GUN CONSOLE to the VIDEO CABINET. A2 Free up the Grn-Yel Ground wires located in the back of the CONSOLE. See 6-3 Fig 06, and run them through to the VIDEO Cabinet connecting them securely to the EARTH POINT located just inside the Cabinet. A3 Locate the Connection Harness ﬁtted in both the VIDEO Cabinet and the GUN CONSOLE, and connect them together (Like to Like). B When all the connection have been made secure. Tuck the spare cable into the SPACER move it towards the VIDEO Cabinet C Line up the CONSOLE with the VIDEO Cabinet so that the ﬁxing brackets are located inside the SPACER. D Close the Gap between both VIDEO Cabinet and CONSOLE and reﬁt the 8 Bolts with both Flat And Spring Washers earlier removed. 6 ASSEMBLY & INSTALLATION A1 Free up the VIDEO Cable located in the Video Cabinet, pass it through into the CONSOLE connecting it to the LINBURGH Game Board. See 6-3 Fig 06. 6-4 INSTALLATION AND SECURING IN PLACE During Installation, make sure that all the adjusters are in contact the ﬂoor. Otherwise the cabinet could move, causing an accident. 6 ASSEMBLY & INSTALLATION . PRIMEVAL HUNTER consists of two Main Base Units : Main Video Cabinet and Gun Console. 6-4 Fig 01 - Shows the location of the Castors (C) and Fixing Adjusters (A). During the installation of each unit, the Fixing Adjustment should be performed to ensure that the units are stable. VIDEO UNIT 6-2 Fig 01 GUN CONSOLE 6-4- Fig 02 - Showing the correct details for Adjustment. 6-5 CONNECTION OF POWER AND GROUND • Use the power supply equipped with an earth leakage breaker. Use of power supply without such a breaker could result in ﬁre if there is a current leakage. • Do not expose the power cords. If these are exposed, customers could stumble over them, for instance, and easily damage them. Additionally, if these lines are damaged, there could be a risk of electrical shock or short circuit. Set these lines at locations where they will not interfere wi